Showing results: 361 - 375 of 582 items found.
-
PRESS-CHECK -
InfraTec GmbH
The automated test system PRESS-CHECK works with two powerful high-end thermographic cameras for continuous measurement of two-dimensional temperature distribution. This measurement is carried out before the pressing operation on the surfaces of the boards to be processed and subsequently on the resulting molded parts, ultimately enabling exact compliance with the thermal process parameters.
-
PCIe-Harpoon -
Dynamic Engineering
PCIe-Harpoon is a multi-functional board with capabilites for isolated measurement and control. The initial use of the PCIe-Harpoon is to simulate - act as if the PCIe-Harpoon was another piece of equipment. The simulation provides a means to test the rest of the equipment without requiring the real [expensive] asset. In addition the PCIe-Harpoon can provide status and direct software control of the system.
-
ViTec Co. Ltd
The use of a 16-bit analog input board provided high measurement accuracy, and the use of the SCXI reconciliation system allowed the integration of signals from the most diverse sensors in one configuration. The software developed at LabVIEW implements all kinds of tests of turbo starters in full accordance with the approved methods.
-
PCI - HARPOON -
Dynamic Engineering
PCI-Harpoon is a multi-functional board with capabilites for isolated measurement and control. The initial use of the PCI-Harpoon is to simulate - act as if the PCI-Harpoon was another piece of equipment. The simulation provides a means to test the rest of the equipment without requiring the real [expensive] asset. In addition the PCI-Harpoon can provide status and direct software control of the system.
-
U800FPC -
Utron Technologies
1. CCD automatic alignment, with an accuracy of ± 10μm2. Support layout test, displacement function3. The upper and lower jigs X, Y, θ are automatically fine-tuned to improve the yield4. Soft board stretching function5. Automatic marking function6. Support SHOPFLOOR report output7. Optional BARCODE READER
-
Delta MATRiX -
Cohu, Inc.
Cohu’s MATRiX handler has a highly flexible test site configuration that’s well suited for a wide range of test applications, including analog ICs with short test times and high throughput, automotive devices requiring accurate thermal control, small pitch wireless-communication products, high parallel microcontroller testing, MEMS device testing, and many other device market segments with their unique requirements. The MATRiX has a highly flexible test site configuration that enables customers to reuse existing load-boards, including boards made for competitor’s legacy handlers.
-
NEOSEM TECHNOLOGY INC
The N3500 is Neosem Technology’s fourth generation memory test system. Specifically designed for Flash Components and Flash Cards, the N3500 tester-on-a-board architecture targets the broadest range of DUT technologies in various form factors and packages. Each Tester Board (or “Blade”) contains 288 I/O pins and 32 DPS supplies. Up to 64 Blades populated in one test head can test over 2000 DUTs in parallel. Neosem Technology’s high parallel DUT count architecture, combined with low capital cost, provides the absolute lowest HVM cost of test.
-
GX6196 -
Marvin Test Solutions, Inc.
The GX6196 is a 6U PXI switch and control board that can be used to create custom switching, signal conditioning, or specific UUT control interfaces. The board provides 96, 2 pole, form A relays, 8 digital I/O lines, and a serial digital interface. All of these resources are available via (5) inter-board connectors which interface to the user defined daughter / mezzanine board. The mezzanine board provides all connections to the unit under test (UUT) via two 78 pin D-sub connectors. The GX6196 is supplied with a front panel which accepts (2) 78 pin D-sub connectors.
-
BoxProber Family -
Test Electronics
6 sided Bed of Nails circuit board test fixture. Probes top bottom and all 4 sides. Central camming mechanism pull plates inward. Mechanically or electrically actuated options. Designed primarily for testing products in plastics. Side access electrically probes outside panel connectors. The unit will also optically read LEDs and key segments off LCD displays. Solenoids will press buttons and servos will turn selector switches. DC motors are used to adjust multiple turn potentiometers. Microphone will detect audio output tones. Top and bottom of circuit boards can also be probed if removable access panels are available. This unit will also probe all 6 sides of a circuit board. This is typically utilized in applications where connector testing is required.
-
Electron Plus
The ASA200 Analog Signature Analyser will assist you in testing, diagnosing and troubleshooting printed circuit boards without powering them (known as ‘power-off testing’).Connected via USB to a compatible PC running our own free software the ASA200 you can easily capture, measure and compare known good signatures (from your ‘golden’ board) with signatures from your suspect board. The built-in gate/bias generator (+/-10V, 100ohm source impedance) can be used to help test active components such as SCR’s, opto-couplers, small relays, TRIAC’s etc. An external dual footswitch can be connected to the ASA200 and can be user configured to control various functions.With the ASA200 we set out to bring the incredibly powerful technique of Analog Signature Analysis to engineers and repair shops at an affordable price.
-
Test Coach Corporation
Test Coach has been delivering the highest quality in-circuit test programs since 1998. Our engineers have the education, experience and expertise needed to solve your most challenging test requirements. We partner with our customers to provide comprehensive test solutions, including consulting on: design for test, recommendations on the best hardware and software options to implement, test strategy, and long term planning for multi board projects. Our expertise allows us to really understand customer requirements, so that quotes are accurate and timely. However, we also understand that sometimes projects can change scope. At Test Coach, we have the flexibility to adapt to changes with as little impact to delivery as possible.
-
Model W4.0 x L6.5 -
D-COAX, Inc.
This portable manual probing station is designed for a versatile, comfortable, and accurate operation on up to 4.0” wafers or 4.0” X 6.5” printed circuit board assemblies. This turn-key, manually operated probing station, model W4.0 x L6.5, is part of the D-COAX commitment to the test and measurement and PCB fabrication industries.
-
OCP NIC 3.0 -
UNH IOL
These test fixtures are necessary for testing within the OCP NIC subgroup (found under the OCP Server Work Group). These fixtures will arrive meeting the OCP NIC 3.0 Specification with a characterization of the boards. These fixtures mate with the OCP form factor connector, and will allow an electrical break out of each signaling lane.
-
863 PR -
Standard Electric Works Co., Ltd
● Two functions in one unit: open phase and phase sequence detection.● Neon light indicators.● Large size alligator clips for easy clipping onto switch- boards terminals.● Allows you to check a wide range of 3-phase power sources.● Special test leads length are available on request.
-
B6700 Series -
Advantest Corp.
B6700 can test as many as 48 burn-in boards in parallel at speeds up to 10 MHz, which helps memory suppliers get their newest products to market faster while also reducing testing costs. An original high performance chamber improves yield by assuring high temperature accuracy while generating high temperature. It also shortens the temperature rise and fall time which leads to shortening the test time.
